SCHEDE E RECENSIONI

McIntosh C28 + MC 2200

Pre e Finale 200 watt

 

 


SCHEDA

Di cosa si tratta:

Ampli Finale


L'importanza di iscrivervi alla newsletter

Produttore:

McIntosh  USA

Caratteristiche:

200 watt - trasformatori d'uscita 33 Kg

Costo:

3.325.000 lire anno 1982 Finale MC 2200

Vasta Gamma di Nuovo Usato disponibili  Click

CARATTERISTICHE

 

 

 

INFO DAL WEB

 


 
Stereo power amplifier which carries an original power guarding circuitry. It hits power-meter the non-carrying model of MC2205. 

Distortion is removed by using the monolithic transistor differential amplifier with few noises for the input side of a power amplifier circuitry. An input signal and a feedback signal are supplied to this differential amplifier. 
The circuitry of the following stage is a voltage amplifying circuit of a Class-A operation, and a driver circuitry and an output circuit adopt a complimentary scheme, carry out the operation near a Class-A, and are reducing crossover distortion.
To the transition of a temperature, this circuitry is designed so that a moderate bias may always start. A power transistor is AB class operation and, as for the bias current, the safeness is maintained by the thermistor. 

The para-push scheme of a single ended is used for an output stage, and it consists of six reliable complimentary power transistors. For an equilibrium nature Emitter-Follower join, a stability is good, and distortion's has decreased and this circuitry has realized B class operation without crossover distortion by adoption of a still more original output bias circuitry. 

The output signal of MC2200 passes an output transformer and is supplied to a termination. Since this transformer is designed match the output-terminal of every impedance, even if it uses which output-terminal, the maximum output is obtained to all the signalling frequencies. 
Moreover, the transformer eliminated that component and this transformer has prevented the corruption of the speaker, when it has a role which protects a speaker in the case of a malfunction of amplifier and a direct current component mixes in an output. 
In order to prevent an output transistor carrying out an overload, the output signal is always supervised by the monitor circuitry of the mac patent. This circuitry will become a high impedance if an Output voltage becomes more than a rate, but this does not have influence on an output. When an output becomes a upper, the signal supplied to an output transistor by the monitor circuitry is restricted, and the output of amplifier short-circuits or it prevents a corruption of an output transistor. This pilot circuit is supervising separately the positive side output signal and the negative side output signal. 

The power guarding system which is an original new circuitry is carried for the stability of play sound, and a tone-quality modification. 
In this circuitry, it has Normal (green) in the front panel, and the structure of operating by a wave comparator with a lamp of Limit (red) original with a mac. This circuitry compares an output wave with an input wave electrically, if that wave difference becomes 0.5%, a Limit lamp will light up and a Normal lamp will go out. Moreover, if a wave difference reaches to 1%, the power guarding circuitry will operate, it prevents amplifier carrying out clipping, and distortion is not reproduced from a speaker, but a speaker is protected simultaneously. Even in this case, amplifier demonstrates the rated maximum output. An input wave and an output wave are compared by IC differential amplifier, and the wave difference by distortion of an output wave is changed into a voltage. Moreover, this voltage is amplified about 100 times and supplied to a Schmidt trigger circuit through a full wave rectifier circuit. 
A Limit lamp is turned on also when amplifier overloads. Even if the status of an overload is very short, the light is switched on the time of the grade which can fully be checked by the eye. In this case, meter displays less than 200W. Also at this time, the voltage obtained from the wave difference is used, and when it becomes higher than the level which makes a Limit lamp turn on, a power guarding circuitry is operated. 
When using a power guarding circuitry, the power guarding switchpoint of a rear surface panel is set as the location of Normal. When this switchpoint is in the location of out, only the Limit lamp operates.
 

 

Form

Stereo power amplifier

Output

stereo:

200W+200W (Output power) 
14.1VRMS (at the time of a 1-ohm load intensity) 
20.0VRMS (at the time of a 2-ohm load intensity) 
28.3VRMS (at the time of a 4-ohm load intensity) 
40.0VRMS (at the time of an 8-ohm load intensity)

mono:

400W (Output power) 
14.1VRMS (at the time of a 0.5-ohm load intensity) 
20.0VRMS (at the time of a 1-ohm load intensity) 
28.3VRMS (at the time of a 2-ohm load intensity) 
40.0VRMS (at the time of a 4-ohm load intensity)

Output load impedance

stereo: 1 ohm, 2ohm, 4ohm, 8ohm 
mono: 0.5 ohm, 1ohm, 2ohm, 4ohm

Output-power band

20Hz - 20kHz

THD (at the time of both ch(es) drive)

0.1% or less (Outputs 0.25W-200W, 20Hz - 20kHz)

Cross modulation distortion

0.1% or less (at the time of an Output power)

Frequency characteristic (at the time of 1W output)

20Hz-20kHz+0 -0.25 dB 
10Hz-100kHz+0 -3.0 dB

SN ratio

95dB or more (at the time of an Output power)

Output voltage

25V

Dumping factor

stereo:

16 (at the time of a 1-ohm load intensity) 
50 (at the time of a 2-ohm load intensity) 
30 (at the time of a 4-ohm load intensity) 
16 (at the time of an 8-ohm load intensity)

mono:

16 (at the time of a 0.5-ohm load intensity) 
50 (at the time of a 1-ohm load intensity) 
30 (at the time of a 2-ohm load intensity) 
16 (at the time of a 4-ohm load intensity)

Input sensitivity/impedance

0.75V, 2.5V/100kohm

The semiconductor used

Silicon transistor: 43 pieces 
Silicon diode: 24 pieces 
IC: Two pieces

Power source

120V, 50Hz/60Hz

Power consumption

70W (at the time of a non-signal) 
550W (at the time of a maximum rating output)

Dimensions

Front panel: Width 407x177mm in height 
Main unit: Width 372x height 167x depth of 368mm

Weight

33.1kg 
39.5kg (at the time of an original packaging)

 

SCHEDA FOTOGRAFICA

 

C28

 

 

 

Mc 2200

 

 

 

 

 

 

VEDIAMO DIETRO

 

 

 

 

 

MANUALE


http://sportsbil.com/mcintosh/Amps/MC2200/MC2200_own.pdf

LINKS

 

http://www.audiocostruzioni.com/r_s/pre/pre-mcintosh-c28/C28.htm.htm#c28 con cabinet

 

 

ALCUNI ANNUNCI USATO

 

 

 

 

 

Home